PREPARE the MOTOR. Everything what you must know
Saturday, April 12th, 2008In this section we will try to put engineering datas and other things that help you in the task of “meter mano” to your car.
Archive for the ‘Tuning Manuals’ Category
WHEELS AND CAR TYRES
Saturday, April 12th, 2008The wheel is an automobile that is in direct contact with the pavement.
Its mission, in addition to bear the weight of the car, is to transmit power from the transmission in order to move the vehicle, and provide direction and adherence in moments of acceleration and deceleration.
TROUBLESHOOTING AND MAINTENANCE OF ELECTRICAL AND MECHANICAL CAR
Saturday, April 12th, 2008TROUBLESHOOTING AND MAINTENANCE OF ELECTRICAL AND MECHANICAL CAR
Triangle breakdowns
Periodic reviews by the driver
1. Clean the vehicle.
2. Change oil filter.
3. Level of engine oil. Change filter.
4. Check cooling sleeves.
5. Level change and coolant.
6. Voltage strap generator, water pump.
7. Battery. Level electrólito.Conexiones
8. Power. Checking spark plugs and cables.
9. Deposit of washer systems.
10. Deposit of lavalunetas.
11. Check connections generator.
12. Check connections engine starts.
13. Level hydraulic clutch.
14. Level of the power steering fluid.
15. Jets of lavafaros.
16. Adjusting the suppliers of washer systems.
17. Checking the status of the brushes of wipers.
18. Check brake pedal travel. Pills.
19. Check trail parking brake.
20. Check tour clutch.
21. Level of change.
22. Level of the brake fluid reservoir.
23. Pressure tires.
24. Grease.
25. Grease hinged door locks.
26. Conservation tools and equipment.
27. Documentation of the vehicle.
The revisions indicated in the service book, were virtually referenced in this relationship while others relate to be carried out in workshops recommended as trademarks.
Revisions levels, fluids and other elements of the vehicle
ifferences between the injection and carburisation
Saturday, April 12th, 2008Differences between the injection and carburisation
In gasoline engines, the mixture is prepared using a carburetor or injection equipment. So far, the carburetor was the most common mixture preparation, mechanical.
Advantages of the injection systems
Saturday, April 12th, 2008dvantages of the injection
Consumer reduced
With the use of carburetors, intake manifolds in the mixtures are produced uneven air / gasoline for each cylinder. The need to form a mixture that even enough to feed cylinder compels most disadvantaged, in general, a quantity of fuel dispensed too high.
CABLES FOR THE INSTALLATION OF A CAR AUDIO
Saturday, April 12th, 2008AUDIO CABLES
It has been said and written about how the quality of cabling can affect the sound of a system and it is true. Not you going to recommend that you spend a fortune, but the difference between a preinstallation speaker wire and cable little more of a Euro metro is perfectly audible. Therefore, as long as you advise adecuéis quality cabling to the level of your audio system.
Incidentally, I recommend this site I saw of Buying and selling New Cars and Used Cars… well, what I ..
MAKING A CAR SUBWOOFER
Saturday, April 12th, 2008Often, the passionate love of tuning you do with your hands installing audio of your car. Respecting the rules of the art of assembly is essential to a facility that works perfectly. The theme we have chosen for this section is affordable for any lover of good cars, so whether you can get down to work.
Let’s build a drawer serious host a subwoofer.
MANUFACTURE OF A CAR SUBWOOFER
COVER THE ROOF OF THE CAR STEP BY STEP. ALL TUNNING
Saturday, April 12th, 2008- Leather, measures of the roof as the car, this case 1.60m long (clearance 10cm + / -) and 1m wide (clearance about 20-30cm but this is inevitable, the width comes from “manufactures”). Price: 25 € meter.
How to paint the car interior
Saturday, April 12th, 2008You can tune in any way from sporting rate Rally
To paint on plastic one must first remove impurities, either rest or silicone waxes which may be in the same, this step is the most important, but since then rose painting, for it must be cleaned well with a rag with thinner, the ideal is that you can remove the plastic and paint to handle it better, either board, air vents, handles external mirrors, etc.,…